Parts for sale off my 1966 Chevy C10 Truck Pickup

Chevy C10 Truck Parts FOR SALE

The parts below came off my 1966 Chevy C10 build
I will keep this updated as best as possible

All can be shipped or unless noted
I accept Paypal or Money Order

Parts for sale that I do not have pics of

  •  Brothers inner bedside replacement panel. Right front shortbed fleetside I have 2 of these. Brand new. Part number IBP66SF – $25 each + shipping
    These are BRAND NEW!
  • Stainless steel bed strips for short bed fleetside. Very good condition. I do have SOME of the bolts for it, but not all. The strips are all there though. $100 (can ship if needed) – SOLD!
  • Fleetside (Wideside) Tailgate. Not in too bad of condition. 90% bodywork done. Driver+ quality – media blasted, and primed -$200 SOLD!
  • Fleetside bedside drivers – "should" replace inner panels. I have one of replacement panels (brand new! $35 value). See pics of bedside below
  • Radiator support bracket (bracket that goes from the support to the top of the radiator–$30
  • Radiator cap. New, but used. Has guage on it. $8 – SOLD!
  • C10 fender emblems. 45 years old. – $30
  • Fleetside front bed panel – rusty at the bottom – sandblasted – $60 Local pickup only
  • Left and right inner fenders – original in decent condition. One of them is missing a bracket that goes from the inner fender and bolts onto the radiator support. You can weld your original bracket to the inner fender–$200 for both
  • Master Cylinder-appears to be newer–$20
  • Original seat (not bad for a 50 year old seat)- local pickup only – SOLD!
  • Orig driveshaft (local pickup only)–$40
  • coil springs (front)–$25
  • coil springs (rear)–$25
  • 4 shocks (both front and back) not original. Have been replaced. Miles unknown–$20
  • Door glass channel run (both sides-very nice. I believe these might have been replaced when the truck was painted in the early 90's)–$10 – SOLD!
  • NEW headlight harness (goes from the core support to the headlights-$25 – SOLD!
  • Trailing arms – sandblasted (a few minor rust holes)–$50 – SOLD!
  • original sway bar–$25
  • Core support (rust on the lower passenger area)–$100
  • Clutch pedal assy–$35
  • gas pedal–$5
  • Spare tire brace–$25
  • Glove box – $5
  • Small block chevy motor mounts NEW!!! These are polyurethane and zinc. They are also the newer side bolt style. $90 new. Only $40
  • Back glass – side glass and vent glass – $175 (minor scratches). Local pickup only

 

Fleetside Bedside – Drivers side  – shortbed
local pickup only
$200

 

 

Right door. Rust on lower inside. Outside doesn't appear to be too bad.
I know this was a paint job done in the early 90's
local pickup only
$200 SOLD!

Also have a left door – Started to patch panel in and out and found a good clean door
$30 as is SOLD!

Chrome Steering TILT column
Includes steering adaptor.
This is a 33" universal, but have mounted it in my 66 Chevy C10
When I got it, it had a problem with the turn signal switch so I bought another one and tried to install it.
I did not get it installed. Just bought another one. The column is fully functional, but of course the turn signals will not work
without installation of the turn signal switch which I am including a new one that I bought for $38.
I paid over $225 + shipping + the adaptor
I have already drilled the slot and holes for the neutral safety switch!!!

Includes shifter lever – shifter handle – tilt handle – turn signal handle

SOLD!

I believe these are off of a 67-72 truck. Not for sure. Wheel covers are SOLD!

Grill Surround (Support)
fresh paint – Driver + quality – nice basecoat/clearcoat
there are 2 bolts that got into the very bottom where the small braces go to the rad support
Both are chewed up, but are hidden
$300 SOLD!

Trailing arm crossmember – $25

Steering column (comes with chrome horn lever/button) – 
Local pickup only

SOLD!

Water Pump – Long for small block chevy. This is brand new and never been used
SOLD!

10 Responses

  1. Chuck D says:
    December 12, 2011 at 10:03 pm

    Interested in your clutch

    Interested in your clutch pedal and maybe some other parts.. Please email back thanks!

  2. tgahner says:
    May 15, 2012 at 4:13 am

    door glass channel run

    this is one of the last parts ive needed to find for a restore me and my sone are doing please tell me u still havwe them. you can contact me at tgahner78@gmail.com

  3. metrofxr says:
    September 18, 2012 at 3:52 am

    R/H inner fender steering shaft cover

     Assume this is still a valid site…? (I Hope) I'm searching for the steering shaft cover assy (P/N 3771285) Bolts up the the R/H inner fender around the shaft… Do you happen to have?

       Thanks

      Chuck

    • ACP says:
      September 18, 2012 at 10:27 am

      Chuck,
      Sorry, I do not have

      Chuck,
      Sorry, I do not have one. I used my original cover for my build.
      I believe you mean "left" inner fender.

       

  4. victorallen says:
    October 28, 2012 at 5:41 pm

    Radiator support bracket

    Hello, do you still have the radiator support bracket for sale? You've done an awesome job on your truck, by the way. My son and I are doing a very similar build on a '65 and I have reallly enjoyed your build documentaion. Thanks.

    • ACP says:
      October 29, 2012 at 10:45 am

      I think I still have it

      I have a lot of parts boxed up. I'll see if I can find it.
      I'll let you know later on today.
      Thanks for the compliment! Hopefully some of the pics will give you some ideas.
       

      Scott